The short answer: traditional Western kitchen knives are often sharpened at about 20 degrees per side. Thinner, Japanese-style knives are often 15 to 16 degrees per side, and many newer German-style knives are made at 14 to 17. These are rules of thumb, and makers differ. If the maker lists an angle for your knife, use that one. It beats any rule of thumb, including the ones in this article.
What "angle" actually means
When people say "20 degrees," they almost always mean degrees per side. That is the angle between one face of the blade and an imaginary line running straight down the middle of the blade.
A knife has two faces, so the whole edge is twice that number. This is called the included angle.
spine
__________
\ / Each side leans in from the center line.
\ / 20 degrees per side = 40 degrees included.
\ / 15 degrees per side = 30 degrees included.
\ /
\/
edge
This matters because some makers and some guides quote the included angle. A sheet that says "30 degrees" might mean 15 per side, and a tool set to 30 per side would give you an edge far too blunt for most kitchen work. Before you set anything, check which number you are looking at. In this article, the angles quoted for knives are per side.
The trade-off: sharper or tougher
Think of the edge as a wedge. A narrow wedge slides through food with very little push. A wide wedge has more steel behind the edge to support it.
- Lower angle (15 degrees): cuts more easily and feels sharper in the hand. The thin edge is more fragile, so it chips or rolls more easily on bones, hard squash, frozen food or a hard cutting board.
- Higher angle (20 to 22 degrees): tougher and more forgiving. It shrugs off hard use and stays usable longer between sharpenings. It does not glide through a tomato quite as lightly.
The right angle is the lowest one your knife and your habits can safely support.
Which angle for which knife
Use this as a starting point. The maker's number always wins.
| Knife | Typical angle (per side) | Notes |
|---|---|---|
| Chef's knife | About 20 for traditional Western knives; 15 to 18 for thinner or newer blades | The most common question. If the blade is slim and light, try a lower angle. |
| Santoku | 15 to 18 | Japanese-style santokus are often 15 to 16. A heavier Western-made santoku may be 20. |
| Utility knife | 15 to 20 | Follow the thickness of the blade. Thin and light, go lower. |
| Cleaver | 20 to 22 | Chopping is hard on an edge, so a sturdier angle holds up better. |
| Paring knife | 18 to 20 | The blade is small. Edgekeep's own FAQ says small paring blades can rock on the guide, so we do not oversell this one. |
| Serrated (bread knife) | Not suitable | The teeth need a different method. Edgekeep does not sharpen serrated knives. |
| Very thin Japanese blades | About 9 to 12 | Below the lowest angle on Edgekeep (15), so we do not promise these. |
The real problem: holding the angle by hand
Choosing the angle is the easy part. Holding it is hard.
On a whetstone, you tilt the blade to what you think is 15 or 20 degrees and keep it there for dozens of strokes. A few degrees of drift changes the edge you are making, and drift creeps in as your wrist tires.
Here is the useful part: consistency matters more than hitting a perfect number. A steady 19 degrees on every pass beats a wandering mix of 15 and 25. That is why guides, clips and angle blocks exist. They take the guessing out of the one thing that is hardest to repeat by hand.
How to keep a steady angle with a magnetic angle block
Here is how it works on Edgekeep, which is built around exactly this problem.
- Pick the grit. Edgekeep has four: 240, 400, 600 and 1000. Go from the coarsest to the finest. The 240 repairs a rough edge, the 400 and 600 refine it, and the 1000 finishes it.
- Set the angle. Click the magnetic block to 15, 18, 20 or 22 degrees.
- Let the block hold the blade. The magnetic block holds the blade at the angle you set, so the knife stays put.
- Roll. Push the roller down the blade, flip the knife, and repeat. The angle does not depend on your wrist, because the block holds it.
The magnetic angle block, marked 15, 18, 20 and 22 degrees.
You can see the whole thing on the Edgekeep Rolling Knife Sharpener page.
If you do not know your knife's angle
Plenty of knives have no printed number. A simple way in:
- Start at 20 degrees. It is the sturdiest of the four settings and a safe choice for most kitchen knives.
- Sharpen, then test. Slice a ripe tomato or a sheet of paper. Notice how it cuts.
- If the blade is thin and light, step down. Try 18, then 15 on the next sharpening.
Treat 20 as a starting point, not a verdict. A very slim, delicate blade was probably made for a lower angle.
Pick one angle per knife and stay with it
Do not change the angle every time you sharpen. Each time you switch, you are creating a new edge geometry, and that means removing steel to reach it.
If you move a knife from 20 to 15 degrees, the first sharpening takes longer and removes more metal, because you have to grind away enough to reach the new, narrower edge. After that, if you stay at 15, each touch-up is quick and light.
So pick one angle per knife and keep to it. The edge is easier to maintain and you waste less steel.
Where Edgekeep fits
Edgekeep is a rolling sharpener with a magnetic angle block. Here is exactly what is in it, and exactly what it is not for.
- Four grits: 240, 400, 600 and 1000.
- Four angles: 15, 18, 20 and 22 degrees, set by clicking the magnetic block.
- Made for straight-edge kitchen knives: chef, santoku, utility and cleaver.
- Not for serrated knives, and not for very thin Japanese blades that want about 9 to 12 degrees.
- Time: a very dull knife, the first time, takes 15 to 30 minutes.
- A 30-Day Money-Back Guarantee: if your knives are not sharper within 30 days of delivery, email your order number and a photo of the kit for a full refund.
If that matches your knives, you can look at the Edgekeep kit here. If it does not, the angle advice above applies to any method.
Frequently asked questions
Is 15 or 20 degrees better?
Neither is better in every case. Fifteen degrees cuts more easily and suits thin, lighter blades, but the edge is more delicate. Twenty degrees is tougher and suits traditional Western knives and heavy use. If your maker gives an angle, use it. If not, start at 20 and step to 15 or 18 for a thin blade.
What angle for a santoku?
Japanese-style santokus are often 15 to 16 degrees per side, so 15 is a good place to start on Edgekeep. A heavier, Western-made santoku may be built for 20. Check the maker's listing if you have it, or start at 18 and see how it cuts.
Can I change my knife's angle?
Yes, but it takes some work. Moving to a lower angle means removing steel to form the new edge, so the first sharpening takes longer. Moving to a higher angle is quicker, because only the very tip of the edge needs regrinding. Once you have changed it, stay at the new angle every time after that.