Edgekeep rolling knife sharpener with a magnetic angle block marked 15, 18, 20 and 22 degrees

How Do You Sharpen a Santoku Knife?

The short answer: find your knife's edge angle, then sharpen both sides at that same angle, working from a coarser grit to a finer one. Japanese-style santokus are often about 15 degrees per side, and heavier Western-made ones may be closer to 20. If the maker lists an angle, use it. Finish by checking that the edge cuts cleanly.

These steps assume a double-bevel santoku, which means both sides of the blade are ground down to the edge. A single-bevel blade, with one flat side, is sharpened differently, so follow the maker's instructions for that knife.

What makes a santoku different

A santoku has a flat, fairly straight edge and a short, wide blade. It is built for push cuts and slicing, which is why it feels so natural for vegetables.

Many santokus are thinner and lighter than a Western chef's knife, and many have a lower edge angle to match. That is why the angle question comes up first.

Which angle to use

The angle is measured per side: it is the tilt of each face of the blade against the sharpening surface.

  • About 15 degrees per side: common on Japanese-style santokus. The edge is thin and cuts with very little force, but it is more delicate.
  • About 20 degrees per side: common on heavier, Western-made santokus. The edge is sturdier and forgives rougher use.

The maker's number always wins. If you cannot find one, a thin, light blade usually wants the lower angle, and a thick, heavy one usually wants the higher angle. Once you pick an angle, keep using it. Changing it every time means grinding away extra steel.

For more on choosing, see what angle to sharpen a kitchen knife.

Those dimples on the blade do not change sharpening

Some santokus have small scallops along the side of the blade, often called a hollow edge. They are there to help thin slices release instead of sticking. They sit above the edge and do not affect how you sharpen it. Sharpen the edge as you would on any other blade.

How to sharpen a santoku, step by step

You can use a whetstone, a guided sharpener, or any tool that holds a steady angle. The order of work is the same.

  1. Clean and dry the knife. Wash off food and oil so you can see the edge.
  2. Choose your starting grit. A very dull or chipped edge needs a coarse grit first. An edge that is only a little tired can start on a medium grit. Do not start coarser than you need to, because coarse grits remove the most steel.
  3. Hold the angle. Keep the blade at the same angle on every stroke. A steady angle matters more than the exact number.
  4. Work one side until you raise a burr. A burr is a thin, rough lip of steel that forms along the opposite side of the edge. Draw a fingertip lightly from the spine toward the edge on the opposite face, never along the edge itself. When you feel a slight catch the whole length of the blade, that side is ready.
  5. Flip the knife and do the other side. Repeat the same number of strokes at the same angle so both sides end up even.
  6. Move to a finer grit. Repeat both sides with lighter pressure. Each step removes the scratches left by the one before it.
  7. Finish with a few light strokes on each side at your finest grit to clear away the burr.
  8. Rinse and dry the knife. Metal dust and grit should not stay on the blade.

Cover the whole edge, from heel to tip, on every pass. A santoku edge is short and mostly straight, with a gentle curve near the tip.

How to test the edge

Do these tests with care.

  • Paper test: hold a sheet of paper by one edge and slice down through it. A sharp edge cuts cleanly without snagging or tearing.
  • Tomato test: a sharp knife bites into the skin of a ripe tomato with only the weight of the blade.
  • Look at the edge: under a bright light, a dull spot can show up as a thin line of reflected light along the edge.

If one section snags, go back to a medium grit and work that spot, then refine again.

The rolling method with Edgekeep

If holding the angle by hand is the hard part, a tool that holds the angle for you helps. Edgekeep is a rolling knife sharpener: a roller with four grits (240, 400, 600 and 1000, coarse to fine) and a magnetic angle block that holds the blade at the angle you set. The block sets 15, 18, 20 or 22 degrees, which includes both angles above.

Edgekeep magnetic angle block marked with the four angles: 15, 18, 20 and 22 degrees

You set the angle, the block holds the blade there, and you roll the roller along the edge. Then you do the other side and move to a finer grit. It is built for straight-edge kitchen knives, such as a chef, santoku or utility knife, and it is not for serrated knives. You can look at the Edgekeep rolling knife sharpener if that sounds like a fit.

Frequently asked questions

What angle should I sharpen a santoku?

Use the angle the maker lists. If you cannot find one, 15 degrees per side suits many Japanese-style santokus, and about 20 suits many heavier Western-made ones. Pick one and stay with it.

Do I need to sharpen both sides of a santoku?

On a double-bevel santoku, yes. Both sides are ground to meet at the edge, so you sharpen each side evenly. A single-bevel blade is different, so follow the maker's guidance for that kind.

How often should I sharpen my santoku?

Sharpen it when it stops cutting cleanly, for example when it crushes a tomato instead of slicing it. Regular honing between sharpenings keeps the edge going longer. How often you sharpen depends on how much you cook and what you cut on.

Back to blog